US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1 Manual de usuario descargar pdf (Pagina 87)

USRobotics

Command Reference

Data Command Set - 79

B V17@14400LT

C V17@14400ST

D-F Reserved

%TT5xyz

"x" corresponds to the desired V.34 bit rate (2400, 4800, 7200, 9600, 12000,

14400, 16800, 19200, 21600, 24000, 26400, 28800, 31200, or 33600):

0 2400

1 4800

2 7200

3 9600

4 12000

5 14400

6 16800

7 19200

8 21600

9 24000

A 26400

B 28800

C 31200

D 33600

E-F Reserved

"y" corresponds to the desired V.34 symbol rate (2400, 2800, 3000, 3200, or

3429).

0 2400 (x = 21600)

1 Reserved

2 2800 (x = 26400)

3 3000 (x = 28800)

4 3200 (x = 31200)

1 2 ... 82 83 84 85 86 87 88 89 90 91 92 ... 157 158

USRobotics Controllerless 1
Command Reference 1
Contents 3
Introduction 9
USRobotics 10
Syntax and Procedures 11
Command Line Editing 12
Command Line Echo 12
Repeating a Command Line 12
Types of DTE Commands 12
Basic Syntax Commands 13
Extended Syntax Commands 14
Action Commands 16
Parameter Commands 17
Issuing Commands 18
Executing Commands 19
Modem Responses 20
Extended Syntax Result Codes 21
Syntax and Procedures - 14 22
Data Command Set 25
Data Command Set - 18 26
Result Code 29
Data Command Set - 23 31
DTE-Modem interface Commands 33
Data Command Set - 26 34
Data Command Set - 28 36
Table 3-1: Result Codes 38
Data Command Set - 32 40
Data Command Set - 34 42
Data Command Set - 37 45
Syntax 47
Data Command Set - 42 50
Data Command Set - 44 52
Modulation Control Commands 54
Data Command Set - 47 55
+MCR: Report Syntax 58
+MRR: Report Syntax 58
Error Control Commands 59
Data Command Set - 54 62
Data Command Set - 56 64
Data Command Set - 59 67
Data Command Set - 61 69
V.8/V.8bis Commands 70
Data Command Set - 63 71
Data Command Set - 65 73
Diagnostic and Test Commands 76
Command Syntax 77
Data Command Set - 70 78
Data Command Set - 72 80
Value Description Notes 82
Data Command Set - 75 83
Data Command Set - 77 85
%TT5xyz 87
Data Command Set - 80 88
Data Command Set - 82 90
Response 92
Data Command Set - 85 93
Data Command Set - 87 95
Example: -QCPS: (0,1) 97
S-Parameters 99
Factory Defaults 100
S-Parameter Definitions 101
S-Parameters - 94 102
S-Parameters - 96 104
S-Parameters - 98 106
Code Message Meaning 108
Fax I/O Processing 115
Fax Origination 117
Fax Answering 117
Fax Control Transmission 117
Fax Control Reception 118
Fax Data Transmission 119
Commands and Parameters 120
Mode Commands 121
Defined Values 122
Result Codes 122
Write Syntax 127
Typical Response 131
Examples 133
Voice Commands 135
Voice Commands - 128 136
Voice Commands - 135 143
Voice Commands - 137 145
Voice Commands - 139 147
Voice Commands - 141 149
Example: 150
Voice Commands - 143 151
Voice Commands - 145 153
+VSP - Speakerphone ON/OFF 155
Voice Commands - 148 156

Comentarios a estos manuales

Sin comentarios

US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1 Manual de usuario Pagina 87

Comentarios a estos manuales

Relacionado con productos y manuales para Módems US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1